Distributor: HEI Conversion

Distributor: HEI conversion Time: 2 hours Tools: standard wrench set, flat-blade andor Phillips screwdriver, wire stripperscrimpers Cost: varies by manufacturer- approximately 175-400 Tinware: HEI distributor (new, rebuilt, or used), HEI ignition lead connector, HEI style wires Tip: Label or mark the location of your spark wires on the distributor cap for fast, easy reference. Tip: When you have installed your HEI distributor, its best to widen the gap as well. Tip: You should run a new wire that is getting a full 12 volts. Simply splicing into the existing lead is not getting maximum to the ignition, as that is a resistance wire. If you measure the juice at idle on that wire, you will find it to be only around 9 volts. The car will run and operate using this wire under normal driving conditions, but the loss will be noticeable at full throttle. Performance gains: increased coil saturation, higher spark output, more reliable The vast majority of cars through the sixties and early seventies were all factory-equipped with a type ignition. Although not likely to be considered the greatest manager of spark, at the time there was no other option. It was not until the model year of 1974 that GM offered the new HEI ignition system as an alternative. One year later in 75, it became standard equipment for all, and with good reason. The GM HEI, which stands for High Energy Ignition, is a breakerless, transistor- controlled, inductive discharge system. It operates in a similar fashion to the conventional type ignition, but relies solely on a series of electronic signals to turn on and off the current rather than the mechanical opening and closing of This task is routinely carried out by the switching transistor- located inside the ignition module. In fact, the HEI distributor is responsible for housing all of its components in one highly self-contained unit. In addition to the module, you will find the ignition coil, the coil, the magnetic assembly, and the mechanical and vacuum advance units all nestled tightly under the cap. I would bet that anyone owning or driving one of these older, system equipped vehicles, at one time or another has run into with their stock ignition systems. Lets face it; are not our friends. No matter what you drive or the application, they always seem to be in a constant state of tune, looking for that elusive (if not imaginary), sweet spot. With so many other improvements that can be made on your car, who wants to spend their time adjusting the dwell angle? Sure, electronic ignitions such as the HEI are a little more expensive than the rebuilt special at your local store. However, in the long run, the time and headaches you spare fiddling with your ignition will more than make up for the initial deficit of a new one. By simply switching over to an electronic distributor, not only do you eliminate the aforementioned hassles of but you will also notice a significant increase in your cars overall From crisper, off-idle throttle response to extra top end the gains to be had by merely removing and replacing your stock distributor with a high HEI are downright impressive. And so, this brings us to the garage. Anytime you the distributor out of the motor, its important to make note of a couple key elements to removal. First off, detach the spark wires and the coil wire, and then remove the cap. Before loosening the distributor clamp and allowing the housing to rotate, mark the of the housing as well as the vacuum advance unit and the rotor, all in relation to the engine block. Loosen the clamp and lightly lift up on the housing. After removing the ignition coil and leads as well as the wires, the distributor is now ready to come out. If the motor is undisturbed while the distributor is out, its simply a matter of reversal at this to install the new HEI unit. Realign your markings and let it fall into DO NOT force it! The teeth of the gears must mesh together in order to fully reseat. Once in hand-tighten the single bolt and clamp to allow for slight adjustability when re-starting the motor. On the other hand, if the motor has been moved, you will need to locate its TDC (top dead center). One easy way to do this without removing the valve covers is to the No. 1 spark Place a finger over the hole and rotate the engine by hand until the compression is felt. When the timing mark on the crankshaft matches up with the 0 on the timing tab, you have reached TDC. Now install the distributor with the rotor at the No. 1 terminal on the cap. When reconnecting the new unit, you will need to and splice in a single HEI terminal connector. This is your hot ignition wire coming from the engine harness. With the ignition coil neatly tucked inside the HEI, it makes the electrical hook-up a cinch. All you need to do here is splice the HEI connector into your existing hot ignition lead. For better see Tips at beginning of this article. The connector then into the cap at the BATT terminal. If you run an aftermarket tachometer, a second connector will be needed. It in adjacent to the ignition lead at the TACH terminal. As I am sure you know by now, type spark wires are not interchangeable with an HEI cap, and vice versa. What a night and day difference between the two! The HEI distributor actually houses the ignition coil underneath that massive cap. You will need to a new set to match your new distributor. With that said, reattach your individual wires to their Take your time and make sure you have them right. With everything finally back together, reconnect the negative battery cable and fire up the engine. Proceed to set the timing, and secure the hold down clamp. Its a good idea to recheck the timing once more to ensure the housing did not move while tightening.